RR2VV-6533B-R6
12-port sector/multibeam antenna, 4x 698–960 MHz 65° HPBW and 8x 1710–2690 MHz 4x 33°HPBW, 6x RET with tilt indicators
Features and Benefits
- All Internal RET actuators are connected in “Cascaded SRET” configuration
- Uses the 4.3-10 connector which is 40 percent smaller than the 7-16 DIN connector
- Enhances network capacity through six sectors on high band while maintaining low band coverage layer through three sectors with only three antenna faces
Specifications
General Specifications
| Antenna Type | Multibeam |
| Band | Multiband |
| Grounding Type | RF connector inner conductor and body grounded to reflector and mounting bracket |
| Performance Note | Outdoor usage |
| Radome Material | Fiberglass, UV resistant |
| Radiator Material | Copper | Low loss circuit board |
| Reflector Material | Aluminum |
| RF Connector Interface | 4.3-10 Female |
| RF Connector Location | Bottom |
| RF Connector Quantity, high band | 8 |
| RF Connector Quantity, low band | 4 |
| RF Connector Quantity, total | 12 |
Remote Electrical Tilt (RET) Information
| RET Hardware | CommRET v2 |
| RET Interface | 8-pin DIN Female | 8-pin DIN Male |
| RET Interface, quantity | 2 female | 2 male |
| Input Voltage | 10–30 Vdc |
| Internal RET | High band (4) | Low band (2) |
| Power Consumption, idle state, maximum | 1 W |
| Power Consumption, normal conditions, maximum | 8 W |
| Protocol | 3GPP/AISG 2.0 (Single RET) |
Dimensions
| Width | 498 mm | 19.606 in |
| Depth | 197 mm | 7.756 in |
| Length | 2100 mm | 82.677 in |
| Net Weight, without mounting kit | 43 kg | 94.799 lb |
Array Layout
| Click on image to enlarge. |
Port Configuration
| Click on image to enlarge. |
Electrical Specifications
| Impedance | 50 ohm |
| Operating Frequency Band | 698 – 960 MHz | 1710 – 2690 MHz |
| Polarization | ±45° |
| Total Input Power, maximum | 1,000 W |
Electrical Specifications
| Frequency Band, MHz | 698–803 | 824–880 | 880–960 | 1710–1880 | 1920–2170 | 2300–2490 | 2490–2690 |
| Gain, dBi | 15.1 | 15.4 | 15.5 | 17.4 | 18.9 | 19.0 | 19.5 |
| Beam Centers, Horizontal, degrees | ±27 | ±25 | ±24 | ±22 | |||
| Beamwidth, Horizontal, degrees | 70 | 64 | 61 | 32 | 29 | 27 | 24 |
| Beamwidth, Vertical, degrees | 10.9 | 9.7 | 9.1 | 8.9 | 7.9 | 6.8 | 6.4 |
| Beam Tilt, degrees | 2–12 | 2–12 | 2–12 | 2–12 | 2–12 | 2–12 | 2–12 |
| USLS (First Lobe), dB | 18 | 18 | 18 | 18 | 20 | 19 | 19 |
| Front-to-Back Ratio at 180°, dB | 30 | 30 | 34 | 34 | 36 | 34 | 33 |
| Front-to-Back Ratio, Copolarization 180° ± 30°, dB | 29 | 28 | 29 | 29 | 31 | 30 | 30 |
| Isolation, Cross Polarization, dB | 25 | 25 | 25 | 25 | 25 | 25 | 25 |
| Isolation, Inter-band, dB | 25 | 25 | 25 | 25 | 25 | 25 | 25 |
| VSWR | Return loss, dB | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 |
| PIM, 3rd Order, 2 x 20 W, dBc | -150 | -150 | -150 | -150 | -150 | -150 | -150 |
| Input Power per Port at 50°C, maximum, watts | 400 | 400 | 400 | 250 | 250 | 250 | 250 |
Electrical Specifications, BASTA
| Frequency Band, MHz | 698–803 | 824–880 | 880–960 | 1710–1880 | 1920–2170 | 2300–2490 | 2490–2690 |
| Gain by all Beam Tilts, average, dBi | 14.7 | 15.1 | 15.3 | 16.7 | 18.4 | 18.4 | 19.1 |
| Gain by all Beam Tilts Tolerance, dB | ±0.4 | ±0.3 | ±0.3 | ±1.2 | ±0.7 | ±1.6 | ±0.8 |
| Gain by Beam Tilt, average, dBi | 2 ° | 14.8 7 ° | 14.812 ° | 14.6 | 2 ° | 15.2 7 ° | 15.212 ° | 14.9 | 2 ° | 15.4 7 ° | 15.412 ° | 15.0 | 2 ° | 16.8 7 ° | 16.812 ° | 15.5 | 2 ° | 18.4 7 ° | 18.512 ° | 18.1 | 2 ° | 18.5 7 ° | 18.612 ° | 18.0 | 2 ° | 19.1 7 ° | 19.312 ° | 18.7 |
| Beamwidth, Horizontal Tolerance, degrees | ±6.1 | ±5.1 | ±3.3 | ±3.1 | ±1.4 | ±2.8 | ±1.2 |
| Beamwidth, Vertical Tolerance, degrees | ±0.7 | ±0.4 | ±0.6 | ±0.6 | ±0.5 | ±0.4 | ±0.5 |
| USLS, beampeak to 20° above beampeak, dB | 17 | 16 | 16 | 13 | 16 | 16 | 15 |
| Front-to-Back Total Power at 180° ± 30°, dB | 21 | 22 | 23 | 28 | 29 | 28 | 28 |
| CPR at Boresight, dB | 21 | 21 | 18 | 16 | 20 | 16 | 22 |
| CPR at Sector, dB | 11 | 8 | 12 | ||||
| CPR at 10 dB Horizontal Beamwidth, dB | 3 | 9 | 9 | 11 |
Mechanical Specifications
| Wind Loading @ Velocity, frontal | 803.0 N @ 150 km/h (180.5 lbf @ 150 km/h) |
| Wind Loading @ Velocity, lateral | 275.0 N @ 150 km/h (61.8 lbf @ 150 km/h) |
| Wind Loading @ Velocity, maximum | 1,040.0 N @ 150 km/h (233.8 lbf @ 150 km/h) |
| Wind Loading @ Velocity, rear | 661.0 N @ 150 km/h (148.6 lbf @ 150 km/h) |
| Wind Speed, maximum | 241.4 km/h (150 mph) |
Packaging and Weights
| Width, packed | 565 mm | 22.244 in |
| Depth, packed | 309 mm | 12.165 in |
| Length, packed | 2287 mm | 90.039 in |
| Weight, gross | 57.4 kg | 126.545 lb |
Regulatory Compliance/Certifications
| Agency | Classification |
| ISO 9001:2015 | Designed, manufactured and/or distributed under this quality management system |
| ROHS | Compliant/Exempted |
CHINA-ROHS
|
Above maximum concentration value |
| UK-ROHS | Compliant/Exempted |
General Specifications
| Antenna Type | Multibeam |
| Band | Multiband |
| Grounding Type | RF connector inner conductor and body grounded to reflector and mounting bracket |
| Performance Note | Outdoor usage |
| Radome Material | Fiberglass, UV resistant |
| Radiator Material | Copper | Low loss circuit board |
| Reflector Material | Aluminum |
| RF Connector Interface | 4.3-10 Female |
| RF Connector Location | Bottom |
| RF Connector Quantity, high band | 8 |
| RF Connector Quantity, low band | 4 |
| RF Connector Quantity, total | 12 |
Remote Electrical Tilt (RET) Information
| RET Hardware | CommRET v2 |
| RET Interface | 8-pin DIN Female | 8-pin DIN Male |
| RET Interface, quantity | 2 female | 2 male |
| Input Voltage | 10–30 Vdc |
| Internal RET | High band (4) | Low band (2) |
| Power Consumption, idle state, maximum | 1 W |
| Power Consumption, normal conditions, maximum | 8 W |
| Protocol | 3GPP/AISG 2.0 (Single RET) |
Dimensions
| Width | 498 mm | 19.606 in |
| Depth | 197 mm | 7.756 in |
| Length | 2100 mm | 82.677 in |
| Net Weight, without mounting kit | 43 kg | 94.799 lb |
Electrical Specifications
| Impedance | 50 ohm |
| Operating Frequency Band | 698 – 960 MHz | 1710 – 2690 MHz |
| Polarization | ±45° |
| Total Input Power, maximum | 1,000 W |
Electrical Specifications
| Frequency Band, MHz | 698–803 | 824–880 | 880–960 | 1710–1880 | 1920–2170 | 2300–2490 | 2490–2690 |
| Gain, dBi | 15.1 | 15.4 | 15.5 | 17.4 | 18.9 | 19.0 | 19.5 |
| Beam Centers, Horizontal, degrees | ±27 | ±25 | ±24 | ±22 | |||
| Beamwidth, Horizontal, degrees | 70 | 64 | 61 | 32 | 29 | 27 | 24 |
| Beamwidth, Vertical, degrees | 10.9 | 9.7 | 9.1 | 8.9 | 7.9 | 6.8 | 6.4 |
| Beam Tilt, degrees | 2–12 | 2–12 | 2–12 | 2–12 | 2–12 | 2–12 | 2–12 |
| USLS (First Lobe), dB | 18 | 18 | 18 | 18 | 20 | 19 | 19 |
| Front-to-Back Ratio at 180°, dB | 30 | 30 | 34 | 34 | 36 | 34 | 33 |
| Front-to-Back Ratio, Copolarization 180° ± 30°, dB | 29 | 28 | 29 | 29 | 31 | 30 | 30 |
| Isolation, Cross Polarization, dB | 25 | 25 | 25 | 25 | 25 | 25 | 25 |
| Isolation, Inter-band, dB | 25 | 25 | 25 | 25 | 25 | 25 | 25 |
| VSWR | Return loss, dB | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 | 1.5 | 14.0 |
| PIM, 3rd Order, 2 x 20 W, dBc | -150 | -150 | -150 | -150 | -150 | -150 | -150 |
| Input Power per Port at 50°C, maximum, watts | 400 | 400 | 400 | 250 | 250 | 250 | 250 |
Electrical Specifications, BASTA
| Frequency Band, MHz | 698–803 | 824–880 | 880–960 | 1710–1880 | 1920–2170 | 2300–2490 | 2490–2690 |
| Gain by all Beam Tilts, average, dBi | 14.7 | 15.1 | 15.3 | 16.7 | 18.4 | 18.4 | 19.1 |
| Gain by all Beam Tilts Tolerance, dB | ±0.4 | ±0.3 | ±0.3 | ±1.2 | ±0.7 | ±1.6 | ±0.8 |
| Gain by Beam Tilt, average, dBi | 2 ° | 14.8; 7 ° | 14.8;12 ° | 14.6 | 2 ° | 15.2; 7 ° | 15.2;12 ° | 14.9 | 2 ° | 15.4; 7 ° | 15.4;12 ° | 15.0 | 2 ° | 16.8; 7 ° | 16.8;12 ° | 15.5 | 2 ° | 18.4; 7 ° | 18.5;12 ° | 18.1 | 2 ° | 18.5; 7 ° | 18.6;12 ° | 18.0 | 2 ° | 19.1; 7 ° | 19.3;12 ° | 18.7 |
| Beamwidth, Horizontal Tolerance, degrees | ±6.1 | ±5.1 | ±3.3 | ±3.1 | ±1.4 | ±2.8 | ±1.2 |
| Beamwidth, Vertical Tolerance, degrees | ±0.7 | ±0.4 | ±0.6 | ±0.6 | ±0.5 | ±0.4 | ±0.5 |
| USLS, beampeak to 20° above beampeak, dB | 17 | 16 | 16 | 13 | 16 | 16 | 15 |
| Front-to-Back Total Power at 180° ± 30°, dB | 21 | 22 | 23 | 28 | 29 | 28 | 28 |
| CPR at Boresight, dB | 21 | 21 | 18 | 16 | 20 | 16 | 22 |
| CPR at Sector, dB | 11 | 8 | 12 | ||||
| CPR at 10 dB Horizontal Beamwidth, dB | 3 | 9 | 9 | 11 |
Mechanical Specifications
| Wind Loading @ Velocity, frontal | 803.0 N @ 150 km/h (180.5 lbf @ 150 km/h) |
| Wind Loading @ Velocity, lateral | 275.0 N @ 150 km/h (61.8 lbf @ 150 km/h) |
| Wind Loading @ Velocity, maximum | 1,040.0 N @ 150 km/h (233.8 lbf @ 150 km/h) |
| Wind Loading @ Velocity, rear | 661.0 N @ 150 km/h (148.6 lbf @ 150 km/h) |
| Wind Speed, maximum | 241.4 km/h (150 mph) |
Packaging and Weights
| Width, packed | 565 mm | 22.244 in |
| Depth, packed | 309 mm | 12.165 in |
| Length, packed | 2287 mm | 90.039 in |
| Weight, gross | 57.4 kg | 126.545 lb |
| Click on image to enlarge. |
| Click on image to enlarge. |
Regulatory Compliance/Certifications
| Agency | Classification |
| ISO 9001:2015 | Designed, manufactured and/or distributed under this quality management system |
| ROHS | Compliant/Exempted |
|
CHINA-ROHS
|
Above maximum concentration value |
| UK-ROHS | Compliant/Exempted |
Documentation & Downloads
Assembly Drawing
Product Information
Product Specification
Warranty
Assembly Drawing
Product Compliance Documentation
Product Information
Product Specification
Warranty
Related Products and Accessories
Included Products
Antennas
-
![]()
BSAMNT-4 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Structural Support, Tools & Accessories
-
![]()
BSAMNT-4 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
-
![]()
BSAMNT-4 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Included Products
Antennas
-
![]()
BSAMNT-4 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Structural Support, Tools & Accessories
-
![]()
BSAMNT-4 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
-
![]()
BSAMNT-4 Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
Other Ways to Browse
