Warning Icon

For other alternatives, please contact us for more information.

0 Replacement products available

RR2HH-6533D-R6

12-port sector/multibeam antenna, 4x 694–960 MHz 65° HPBW and 8x 1695–2400 MHz 4x 33°HPBW, 6x RET with tilt indicators
Specifications
Finish making your selections or clear them to view relevant specifications.
How to Buy
Features and Benefits
  • All Internal RET actuators are connected in “Cascaded SRET” configuration
  • Uses the 4.3-10 connector which is 40 percent smaller than the 7-16 DIN connector
  • Enhances network capacity through six sectors on high band while maintaining low band coverage layer through three sectors with only three antenna faces
Specifications

General Specifications

Antenna Type Multibeam
Band Multiband
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
Radome Material Fiberglass, UV resistant
Radiator Material Copper | Low loss circuit board
Reflector Material Aluminum
RF Connector Interface 4.3-10 Female
RF Connector Location Bottom
RF Connector Quantity, high band 8
RF Connector Quantity, low band 4
RF Connector Quantity, total 12

Remote Electrical Tilt (RET) Information, General

RET Hardware CommRET v2
RET Interface 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity 2 female | 2 male

Dimensions

Width 498 mm | 19.606 in
Depth 197 mm | 7.756 in
Length 2688 mm | 105.827 in

Array Layout

Click on image to enlarge.

Port Configuration

Click on image to enlarge.

Electrical Specifications

Impedance 50 ohm
Operating Frequency Band 694 – 960 MHz | 1695 – 2400 MHz
Polarization ±45°
Total Input Power, maximum 700 W @ 50 °C

Remote Electrical Tilt (RET) Information, Electrical

Protocol 3GPP/AISG 2.0 (Single RET)
Power Consumption, idle state, maximum 1 W
Power Consumption, normal conditions, maximum 8 W
Input Voltage 10–30 Vdc
Internal RET High band (4) | Low band (2)

Electrical Specifications

Frequency Band, MHz 698–806 806–896 880–960 1695–1880 1850–1990 1920–2180 2300–2400
Gain, dBi 15.7 16.0 16.4 17.9 18.7 19.3 19.2
Beam Centers, Horizontal, degrees ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 67 64 61 32 31 30 30
Beamwidth, Vertical, degrees 8.8 7.8 7.4 7.3 6.9 6.5 5.7
Beam Tilt, degrees 2–12 2–12 2–12 2–12 2–12 2–12 2–12
USLS (First Lobe), dB 18 19 19 17 17 18 22
Front-to-Back Ratio at 180°, dB 32 31 31 35 35 36 34
Isolation, Cross Polarization, dB 28 28 28 25 25 25 25
Isolation, Inter-band, dB 30 30 30 30 30 30 30
Isolation, Beam to Beam, dB 17 17 17 17
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port at 50°C, maximum, watts 300 300 300 150 150 150 150

Electrical Specifications, BASTA

Frequency Band, MHz 698–806 806–896 880–960 1695–1880 1850–1990 1920–2180 2300–2400
Gain by all Beam Tilts, average, dBi 15.4 15.8 16.0 17.2 18.2 18.7 18.5
Gain by all Beam Tilts Tolerance, dB ±0.4 ±0.4 ±0.4 ±1.3 ±0.6 ±0.8 ±1.6
Gain by Beam Tilt, average, dBi 2 ° | 15.3
7 ° | 15.5
12 ° | 15.3
2 ° | 15.7
7 ° | 15.9
12 ° | 15.7
2 ° | 15.8
7 ° | 16.1
12 ° | 15.9
2 ° | 17.0
7 ° | 17.3
12 ° | 16.9
2 ° | 18.0
7 ° | 18.3
12 ° | 17.9
2 ° | 18.5
7 ° | 18.9
12 ° | 18.4
2 ° | 18.5
7 ° | 18.8
12 ° | 18.1
Beamwidth, Horizontal Tolerance, degrees ±6 ±4.7 ±3.4 ±2.4 ±1.2 ±1.6 ±1.4
Beamwidth, Vertical Tolerance, degrees ±0.6 ±0.4 ±0.5 ±0.4 ±0.3 ±0.5 ±0.3
USLS, beampeak to 20° above beampeak, dB 17 16 17 15 16 16 13
Front-to-Back Total Power at 180° ± 30°, dB 21 22 22 29 30 30 29
CPR at Boresight, dB 19 18 18 16 16 18 13
CPR at Sector, dB 11 8 11
CPR at 10 dB Horizontal Beamwidth, dB 4 7 8 9

Mechanical Specifications

Wind Loading at Velocity, frontal 1,070.0 N @ 150 km/h
Wind Loading at Velocity, lateral 375.0 N @ 150 km/h
Wind Loading at Velocity, maximum 1,385.0 N @ 150 km/h | 311.4 lbf @ 150 km/h
Wind Loading at Velocity, rear 880.0 N @ 150 km/h
Wind Speed, maximum 241.4016 km/h | 150.000 mph

Packaging and Weights

Width, packed 608 mm | 23.937 in
Depth, packed 352 mm | 13.858 in
Length, packed 2880 mm | 113.386 in
Net Weight, without mounting kit 54 kg | 119.049 lb
Weight, gross 78 kg | 171.96 lb

Regulatory Compliance/Certifications

Agency Classification
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
ROHS Compliant/Exempted
CHINA-ROHS Above maximum concentration value

General Specifications

Antenna Type Multibeam
Band Multiband
Grounding Type RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note Outdoor usage | Wind loading figures are validated by wind tunnel measurements described in white paper WP-112534-EN
Radome Material Fiberglass, UV resistant
Radiator Material Copper | Low loss circuit board
Reflector Material Aluminum
RF Connector Interface 4.3-10 Female
RF Connector Location Bottom
RF Connector Quantity, high band 8
RF Connector Quantity, low band 4
RF Connector Quantity, total 12

Remote Electrical Tilt (RET) Information, General

RET Hardware CommRET v2
RET Interface 8-pin DIN Female | 8-pin DIN Male
RET Interface, quantity 2 female | 2 male

Dimensions

Width 498 mm | 19.606 in
Depth 197 mm | 7.756 in
Length 2688 mm | 105.827 in

Electrical Specifications

Impedance 50 ohm
Operating Frequency Band 694 – 960 MHz | 1695 – 2400 MHz
Polarization ±45°
Total Input Power, maximum 700 W @ 50 °C

Remote Electrical Tilt (RET) Information, Electrical

Protocol 3GPP/AISG 2.0 (Single RET)
Power Consumption, idle state, maximum 1 W
Power Consumption, normal conditions, maximum 8 W
Input Voltage 10–30 Vdc
Internal RET High band (4) | Low band (2)

Electrical Specifications

Frequency Band, MHz 698–806 806–896 880–960 1695–1880 1850–1990 1920–2180 2300–2400
Gain, dBi 15.7 16.0 16.4 17.9 18.7 19.3 19.2
Beam Centers, Horizontal, degrees ±27 ±27 ±27 ±27
Beamwidth, Horizontal, degrees 67 64 61 32 31 30 30
Beamwidth, Vertical, degrees 8.8 7.8 7.4 7.3 6.9 6.5 5.7
Beam Tilt, degrees 2–12 2–12 2–12 2–12 2–12 2–12 2–12
USLS (First Lobe), dB 18 19 19 17 17 18 22
Front-to-Back Ratio at 180°, dB 32 31 31 35 35 36 34
Isolation, Cross Polarization, dB 28 28 28 25 25 25 25
Isolation, Inter-band, dB 30 30 30 30 30 30 30
Isolation, Beam to Beam, dB 17 17 17 17
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0
PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150 -150 -150
Input Power per Port at 50°C, maximum, watts 300 300 300 150 150 150 150

Electrical Specifications, BASTA

Frequency Band, MHz 698–806 806–896 880–960 1695–1880 1850–1990 1920–2180 2300–2400
Gain by all Beam Tilts, average, dBi 15.4 15.8 16.0 17.2 18.2 18.7 18.5
Gain by all Beam Tilts Tolerance, dB ±0.4 ±0.4 ±0.4 ±1.3 ±0.6 ±0.8 ±1.6
Gain by Beam Tilt, average, dBi 2 ° | 15.3; 7 ° | 15.5;12 ° | 15.3 2 ° | 15.7; 7 ° | 15.9;12 ° | 15.7 2 ° | 15.8; 7 ° | 16.1;12 ° | 15.9 2 ° | 17.0; 7 ° | 17.3;12 ° | 16.9 2 ° | 18.0; 7 ° | 18.3;12 ° | 17.9 2 ° | 18.5; 7 ° | 18.9;12 ° | 18.4 2 ° | 18.5; 7 ° | 18.8;12 ° | 18.1
Beamwidth, Horizontal Tolerance, degrees ±6 ±4.7 ±3.4 ±2.4 ±1.2 ±1.6 ±1.4
Beamwidth, Vertical Tolerance, degrees ±0.6 ±0.4 ±0.5 ±0.4 ±0.3 ±0.5 ±0.3
USLS, beampeak to 20° above beampeak, dB 17 16 17 15 16 16 13
Front-to-Back Total Power at 180° ± 30°, dB 21 22 22 29 30 30 29
CPR at Boresight, dB 19 18 18 16 16 18 13
CPR at Sector, dB 11 8 11
CPR at 10 dB Horizontal Beamwidth, dB 4 7 8 9

Mechanical Specifications

Wind Loading at Velocity, frontal 1,070.0 N @ 150 km/h
Wind Loading at Velocity, lateral 375.0 N @ 150 km/h
Wind Loading at Velocity, maximum 1,385.0 N @ 150 km/h | 311.4 lbf @ 150 km/h
Wind Loading at Velocity, rear 880.0 N @ 150 km/h
Wind Speed, maximum 241.4016 km/h | 150.000 mph

Packaging and Weights

Width, packed 608 mm | 23.937 in
Depth, packed 352 mm | 13.858 in
Length, packed 2880 mm | 113.386 in
Net Weight, without mounting kit 54 kg | 119.049 lb
Weight, gross 78 kg | 171.96 lb
Click on image to enlarge.
Click on image to enlarge.

Regulatory Compliance/Certifications

Agency Classification
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
ROHS Compliant/Exempted
CHINA-ROHS Above maximum concentration value
Other Ways to Browse