For other alternatives, please contact us for more information.

0 Alternative products available

NHHSS-55C-R2BT4

10-port sector antenna, 2x 698–896, 4x 1695–2200 and 4x 3100-4000 MHz, 55° HPBW, 2x RETs.

Find a Partner

Specifications

Finish making your selections or clear them to view relevant specifications.

Features and Benefits

Utilizes Pattern Shaping Technology to reduce cell overlap and maximize SINR (Signal to Interference and Noise Ratio)
Superior SPR (Sector Power Ratio) for best-in-class data throughput rates
Excellent pattern overlay across all bands
Low band and mid band performance mirrors performance of the equivalent hex port antenna
Internal SBTs on low and mid band allow remote RET control from the radio over the RF jumper cable
One LB RET and one MB RET. Both mid band arrays are controlled by one RET to ensure same tilt level for best 4x4 MIMO performance
Use optional BSAMNT-SBS-2-2 for side-by-side mounting of two hex and/or ten port 55° antennas

Specifications

General Specifications

Antenna Type	Sector
Band	Multiband
Color	Light Gray (RAL 7035)
Grounding Type	RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note	Outdoor usage
Radome Material	Fiberglass, UV resistant
Radiator Material	Low loss circuit board
Reflector Material	Aluminum
RF Connector Interface	4.3-10 Female
RF Connector Location	Bottom
RF Connector Quantity, high band	4
RF Connector Quantity, mid band	4
RF Connector Quantity, low band	2
RF Connector Quantity, total	10

Remote Electrical Tilt (RET) Information

RET Hardware	CommRET v2
RET Interface, quantity	2 female \| 2 male
Input Voltage	10–30 Vdc
Internal Bias Tee	Port 1 \| Port 3
Internal RET	Low band (1) \| Mid band (1)
Power Consumption, active state, maximum	10 W
Power Consumption, idle state, maximum	2 W
Protocol	3GPP/AISG 2.0 (Single RET)

Dimensions

Width	395 mm \| 15.551 in
Depth	228 mm \| 8.976 in
Length	2438 mm \| 95.984 in
Net Weight, antenna only	35.4 kg \| 78.044 lb

Array Layout

Click on image to enlarge.

Port Configuration

Click on image to enlarge.

Electrical Specifications

Impedance	50 ohm
Operating Frequency Band	698 – 896 MHz \| 1695 – 2200 MHz \| 3100 – 4000 MHz
Polarization	±45°
Total Input Power, maximum	1,000 W @ 50 °C

Electrical Specifications

	R1	R1	B1,B2	B1,B2	B1,B2	P1,P2	P1,P2	P1,P2
Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	3100–3550	3550–3700	3700–4000
RF Port	1,2	1,2	3,4,5,6	3,4,5,6	3,4,5,6	7,8,9,10	7,8,9,10	7,8,9,10
Gain, dBi	16.2	16.1	18.0	18.2	18.5	17.7	17.6	17.4
Beamwidth, Horizontal, degrees	57	54	56	59	57	56	62	52
Beamwidth, Vertical, degrees	9.3	8.1	5.6	5.2	4.8	5.9	5.3	5.2
Beam Tilt, degrees	0–11	0–11	0–7	0–7	0–7	4	4	4
USLS (First Lobe), dB	15	16	18	19	19	19	21	15
Front-to-Back Ratio at 180°, dB	26	30	31	33	31	29	26	24
Isolation, Cross Polarization, dB	25	25	25	25	25	25	25	25
Isolation, Inter-band, dB	25	25	25	25	25	30	30	30
VSWR \| Return loss, dB	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0
PIM, 3rd Order, 2 x 20 W, dBc	153	153	153	153	153	145	145	145
Input Power per Port at 50°C, maximum, watts	250	250	200	200	200	100	100	100

Electrical Specifications, BASTA

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	3100–3550	3550–3700	3700–4000
Gain by all Beam Tilts, average, dBi	15.8	15.8	17.5	18.0	18.2	17.5	17.3	17.1
Gain by all Beam Tilts Tolerance, dB	±0.7	±0.5	±0.8	±0.3	±0.4	±0.6	±0.4	±0.6
Beamwidth, Horizontal Tolerance, degrees	±3	±2	±4	±4	±6	±6	±4	±10
Beamwidth, Vertical Tolerance, degrees	±1.3	±0.5	±0.4	±0.2	±0.4	±0.5	±0.3	±0.3
USLS, beampeak to 20° above beampeak, dB	13	15	14	16	16	12	13	14
Front-to-Back Total Power at 180° ± 30°, dB	23	27	27	29	29	24	22	21
CPR at Boresight, dB	21	26	17	24	27	14	15	15

Mechanical Specifications

Effective Projective Area (EPA), frontal	0.36 m² \| 3.875 ft²
Effective Projective Area (EPA), lateral	0.32 m² \| 3.444 ft²
Wind Loading @ Velocity, frontal	382.0 N @ 150 km/h (85.9 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral	346.0 N @ 150 km/h (77.8 lbf @ 150 km/h)
Wind Loading @ Velocity, maximum	768.0 N @ 150 km/h (172.7 lbf @ 150 km/h)
Wind Loading @ Velocity, rear	437.0 N @ 150 km/h (98.2 lbf @ 150 km/h)
Wind Speed, maximum	241 km/h (150 mph)

Packaging and Weights

Width, packed	505 mm \| 19.882 in
Depth, packed	386 mm \| 15.197 in
Length, packed	2570 mm \| 101.181 in
Weight, gross	51 kg \| 112.436 lb

Regulatory Compliance/Certifications

Agency	Classification
ISO 9001:2015	Designed, manufactured and/or distributed under this quality management system
ROHS	Compliant/Exempted
CHINA-ROHS	Above maximum concentration value
UK-ROHS	Compliant/Exempted

General Specifications

Antenna Type	Sector
Band	Multiband
Color	Light Gray (RAL 7035)
Grounding Type	RF connector inner conductor and body grounded to reflector and mounting bracket
Performance Note	Outdoor usage
Radome Material	Fiberglass, UV resistant
Radiator Material	Low loss circuit board
Reflector Material	Aluminum
RF Connector Interface	4.3-10 Female
RF Connector Location	Bottom
RF Connector Quantity, high band	4
RF Connector Quantity, mid band	4
RF Connector Quantity, low band	2
RF Connector Quantity, total	10

Remote Electrical Tilt (RET) Information

RET Hardware	CommRET v2
RET Interface, quantity	2 female \| 2 male
Input Voltage	10–30 Vdc
Internal Bias Tee	Port 1 \| Port 3
Internal RET	Low band (1) \| Mid band (1)
Power Consumption, active state, maximum	10 W
Power Consumption, idle state, maximum	2 W
Protocol	3GPP/AISG 2.0 (Single RET)

Dimensions

Width	395 mm \| 15.551 in
Depth	228 mm \| 8.976 in
Length	2438 mm \| 95.984 in
Net Weight, antenna only	35.4 kg \| 78.044 lb

Electrical Specifications

Impedance	50 ohm
Operating Frequency Band	698 – 896 MHz \| 1695 – 2200 MHz \| 3100 – 4000 MHz
Polarization	±45°
Total Input Power, maximum	1,000 W @ 50 °C

Electrical Specifications

	R1	R1	B1,B2	B1,B2	B1,B2	P1,P2	P1,P2	P1,P2
Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	3100–3550	3550–3700	3700–4000
RF Port	1,2	1,2	3,4,5,6	3,4,5,6	3,4,5,6	7,8,9,10	7,8,9,10	7,8,9,10
Gain, dBi	16.2	16.1	18.0	18.2	18.5	17.7	17.6	17.4
Beamwidth, Horizontal, degrees	57	54	56	59	57	56	62	52
Beamwidth, Vertical, degrees	9.3	8.1	5.6	5.2	4.8	5.9	5.3	5.2
Beam Tilt, degrees	0–11	0–11	0–7	0–7	0–7	4	4	4
USLS (First Lobe), dB	15	16	18	19	19	19	21	15
Front-to-Back Ratio at 180°, dB	26	30	31	33	31	29	26	24
Isolation, Cross Polarization, dB	25	25	25	25	25	25	25	25
Isolation, Inter-band, dB	25	25	25	25	25	30	30	30
VSWR \| Return loss, dB	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0	1.5 \| 14.0
PIM, 3rd Order, 2 x 20 W, dBc	153	153	153	153	153	145	145	145
Input Power per Port at 50°C, maximum, watts	250	250	200	200	200	100	100	100

Electrical Specifications, BASTA

Frequency Band, MHz	698–806	806–896	1695–1880	1850–1990	1920–2200	3100–3550	3550–3700	3700–4000
Gain by all Beam Tilts, average, dBi	15.8	15.8	17.5	18.0	18.2	17.5	17.3	17.1
Gain by all Beam Tilts Tolerance, dB	±0.7	±0.5	±0.8	±0.3	±0.4	±0.6	±0.4	±0.6
Beamwidth, Horizontal Tolerance, degrees	±3	±2	±4	±4	±6	±6	±4	±10
Beamwidth, Vertical Tolerance, degrees	±1.3	±0.5	±0.4	±0.2	±0.4	±0.5	±0.3	±0.3
USLS, beampeak to 20° above beampeak, dB	13	15	14	16	16	12	13	14
Front-to-Back Total Power at 180° ± 30°, dB	23	27	27	29	29	24	22	21
CPR at Boresight, dB	21	26	17	24	27	14	15	15

Mechanical Specifications

Effective Projective Area (EPA), frontal	0.36 m² \| 3.875 ft²
Effective Projective Area (EPA), lateral	0.32 m² \| 3.444 ft²
Wind Loading @ Velocity, frontal	382.0 N @ 150 km/h (85.9 lbf @ 150 km/h)
Wind Loading @ Velocity, lateral	346.0 N @ 150 km/h (77.8 lbf @ 150 km/h)
Wind Loading @ Velocity, maximum	768.0 N @ 150 km/h (172.7 lbf @ 150 km/h)
Wind Loading @ Velocity, rear	437.0 N @ 150 km/h (98.2 lbf @ 150 km/h)
Wind Speed, maximum	241 km/h (150 mph)

Packaging and Weights

Width, packed	505 mm \| 19.882 in
Depth, packed	386 mm \| 15.197 in
Length, packed	2570 mm \| 101.181 in
Weight, gross	51 kg \| 112.436 lb

Click on image to enlarge.

Regulatory Compliance/Certifications

Agency	Classification
ISO 9001:2015	Designed, manufactured and/or distributed under this quality management system
ROHS	Compliant/Exempted
CHINA-ROHS	Above maximum concentration value
UK-ROHS	Compliant/Exempted